A dotted nanowire arrayed by 5 nm sized palladium and nickel composite nanopaticles showing significant electrocatalytic activity towards ethanol oxidation reaction (EOR)

To the best of our knowledge, this is the first time to report the preparation of a dotted nanowire arrayed by 5 nm sized palladium and nickel composite nanoparticles (denoted as Pd_xNi_y NPs) via a hydrothermal method using NU and PdO·H₂O as the starting materials. The samples prepared at the mass ratio of NU to PdO·H₂O 1:1, 1:2 and 2:1 were, respectively, nominated as catalyst c₁, c₂ and c₃. The chemical compositions of all synthesized catalysts were mainly studied by using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), revealing that metallic Ni was one main component of all prepared catalysts. Surprisingly, the main diffraction peaks appearing in the XRD patterns of all prepared catalysts were assigned to the metallic Ni rather than the metallic Pd. Very interestingly, as indicated by the TEM images, a large number of dotted nanowires arrayed by numerous equidistant 5 nm sized nanoparticles were distinctly exhibited in catalyst c₁. More importantly, when being used as electrocatalysts for EOR, all prepared catalysts exhibited an evident electrocatalytic activity towards EOR. In the cyclic voltammetry (CV) test, the peak current density of the forward peak of EOR on catalyst c₁ measured at 50 mV s^?1 was as high as 56.1 mA cm^?2, being almost 9 times higher than that of EOR on catalyst c₃ (6.3 mA cm^?2). Particularly, the polarized current density of EOR on catalyst c₁ at 3600 s, as indicated by the chronoamperometry (CA) experiment, was still maintained to be around 1.47 mA cm^?2, a value higher than the latest reported data of 1.3 mA cm^?2 (measured on the pure Pd/C electrode). Presenting a novel method to prepare dotted nanowires arranged by 5 nm sized nanoparticles and showing the significant eletrocatalytic activities of the newly prepared dotted nanowires towards EOR were the major contributions of this preliminary work.     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

Effect of Ba nonstoichiometry on the phase composition,microstructure, chemical stability and electrical conductivity of BaxCe0.7Zr0.1Y0.1Yb0.1O3−δ (0.9≤x≤1.1) proton conductors

The perovskite proton conductors Ba_xCe_0.7Zr_0.1Y_0.1Yb_0.1O_3−δ (x=0.9, 0.94, 0.98, 1.0, 1.03, 1.06, and 1.1) have been successfully prepared by the conventional solid state reaction route. X-ray diffraction (XRD) patterns of the samples indicate that Ba_xCe_0.7Zr_0.1Y_0.1Yb_0.1O_3−δ (x≥1.0) samples possess a single phase orthorhombic structure, but a secondary phase (Y,Ce)O_2−δ exists in Ba_xCe_0.7Zr_0.1Y_0.1Yb_0.1O_3−δ (x<1.0) samples. SEM photographs show that the grain size of Ba_xCe_0.7Zr_0.1Y_0.1Yb_0.1O_3−δ increases and the porosity decreases with Ba²⁺ content varying from x=0.9 to 1.1. Because of ZnO addition as sintering aid, the sintering temperature of the samples reduces from 1550 °C to 1250 °C. The chemical stability of the samples against CO₂ decreases with the increase in Ba content from x=0.9 to 1.1. All the samples show a excellent stability against water vapor at 850 °C. The conductivities of the samples increase and the activation energies reduce with the increase in Ba content. The present results suggest that it is very important to control the stoichiometry of cations to obtain desired perovskite type high temperature proton conductors.     

焙烧铁尾矿制备透水砖试验研究

为了改善尾矿制砖的力学性质，解决尾矿堆积问题，采用焙烧铁尾矿、水泥和粉煤灰为胶凝材料，2.36~4.75 mm粒级铁尾矿为粗骨料，通过搅拌、成型和养护工艺制备透水砖，探究了焙烧铁尾矿用量、水胶比、目标孔隙率和振动时间对透水砖性能的影响，对比未焙烧尾矿制备透水砖的性能。结果表明：① 焙烧尾矿制备透水砖最佳试验条件为：焙烧尾矿掺量60%，振动时间40 s、水胶比0.3，目标孔隙率20%；此时，透水砖抗折强度为3.34 MPa，符合国家标准Rf3.0，抗压强度为15.44 MPa，符合国家标准MU15，透水系数为2.58×10-2 cm/s，符合国家标准A级标准，实测孔隙率为23.41%。② 焙烧尾矿掺量为60%时效果最佳；未焙烧尾矿掺量为50%时效果最佳，抗折、抗压强度分别为3.38 MPa和14.54 MPa，透水系数符合国家A级标准；焙烧尾矿比未焙烧尾矿多替代水泥10%的情况下，力学性能焙烧尾矿透水砖较好，而透水性能则未焙烧尾矿透水砖较好。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

冷轧退火对FeMnCoCrAl高熵合金组织和力学性能的影响

使用真空电弧炉熔炼出(Fe₅₀Mn₃₀Co₁₀Cr₁₀)₉₄Al₆合金,利用冷轧及在不同温度对合金进行退火,以期望得到由多尺度再结晶晶粒构成的层状结构;并对不同退火温度的样品进行拉伸性能测试。利用扫描电镜和EBSD对合金组织形貌进行表征,采用X射线衍射方法研究其相组成。结果表明:合金在铸态和冷轧后相组成未发生变化,700 ℃退火得到较好的多尺度再结晶晶粒的层状结构,其屈服强度为487 MPa,抗拉强度为708 MPa,断后伸长率为39%,表现出良好的综合力学性能。     

VS2005—高校实验设备网络化管理的利器

高校实验设备实施网络化管理,能够极大提高设备信息的透明度,提高实验设备管理的效率,进一步优化管理工作.VS2005是开发高校设备管理网站的一种简单易学、功能强大的工具.现给出了一个基本的高校实验设备管理网站开发的全过程.     

台阶爆破岩石破碎块度分布的数学模型

以ＫＵＺ－ＲＡＭ模型为基础，提出了岩石系数和均匀性指数的确定方法，由此建立的数学模型在水厂铁矿爆破试验中得到了验证。     

从环己烷氧化液酸洗水中回收己二酸的技术进展

介绍了由环己烷氧化液酸洗水中回收副产的己二酸的方法,主要分析了溶剂萃取法、氧化法、皂化-酯化法的特点及其存在的缺点,指出今后应着重开发新型的己二酸萃取剂,寻求环保型的化学回收方法,并加强对酸洗水新型氧化剂的研究。